Tag Archives: gCode

Printing With Steel on the Printrbot Simple

printrbot

One of the most popular pages on this blog is Calibrating the Printrbot Simple. To be honest I haven’t been using my Simple much lately, what with the hullabaloo surrounding my Barbie-Compatible 3D printed armor Kickstarter. Just don’t have the time.

My mental juice can’t be occupied by all Kickstarter, all the time, so I took a few hours to mess around with Mr. Simple, and I decided to try an experiment that’s long been tugging at my frontal lobes. Can I print something recognizable, in metal, using my Printrbot simple and some clever engineering?

There are hobbyist metal printers on the way. I saw Vader Systems’ prototype at Maker Faire NYC, and can’t wait to get one of these bad boys into the basement at Zheng Labs.

But! Enough wishful thinking. Let’s get down to brass tacks.

I’m using baling wire for this project. You can get this stuff at any hardware store. Just make sure it’s not galvanized, because that can give off some nasty zinc fumes when it’s heated up. Also, I highly advise wearing protective gear.

wire

warning Attempt this project at your own risk! There is an excellent chance that you’ll completely junk your Printrbot, or at least melt the plastic collar at the top of the extruder nozzle. Have a fire extinguisher handy, just in case. Goggles, gloves, the whole nine yards. Be smarter than I was: under no circumstances should you down three mimosas before trying this, no matter how much fun you were having at brunch.

As a precaution, you’ll also want to cover the print bed in fire-retardant tape, unless you’re willing to deal with a flaming Printrbot.

I’m planning on doing this repeatedly, so I replaced the Printrbot Simple’s print bed with a piece of asbestos tile instead. Yay for Open Source!

I just redid the kids’ room with asbestos tile and had some left over. It’s cheap and durable and I can’t believe people just throw this stuff away. Watch this space for a blog post about turning old asbestos tile into cutting boards; I’ll be putting them on Etsy once I’ve cut a dozen of them or so.

Temperature is everything here and you’ll have to move quickly once you start, so be sure to have your gCode pre-generated. Don’t waste time slicing the model before you print.

Preheat the extruder as high as you can get it. I managed to get mine up to 275°C by disabling the firmware safeties and working under heat lamps in the basement. (Printrbot firmware hacking is a topic for another day.)

Even 275°C is way too low for melting steel, so you’ve got to help the Simple across the finish line by heating your baling wire up with a propane torch. Depending on the alloy of your wire that means somewhere around 1400°C, which should be within the range of a hardware store torch.

tip

Start the print and gently feed the hot wire into the Simple’s extruder. I epoxied a steel washer onto the collar of the extruder nozzle to protect it from the hot wire. Don’t lick the glowy part!

The print was a miserable failure, just your typical tangle of filament touched by His Noodly Appendage, ramen. This is what happens when you leave steel prints unattended:

print failure

The second time through I stayed with the print, keeping the propane flame focused on the wire as extruder pulled it in.

feed

With just a little filing and polishing the nose ring looks way better than I expected it to. Not bad for a printer kit that retails for $300, even if I did have to babysit the print the entire time.

yurenjiekuaile

Permit me a brief foray into my other hobby, studying Mandarin Chinese. It’s a remarkably concise language, so cramming the entire One Ring poem (to find them, bind them, yadda yadda yadda) onto the side of the ring is easy peasy lemon squeezy.

You can compress the whole poem into five characters, 愚人节快乐. Way fewer than required in the Black Speech of Mordor.

Flagrant stagecraft alert: I printed the ring and nose separately and welded them together afterwards; I haven’t tried printing anything with support yet.

You can download the STL files for the nose ring in the Baubles section of The Forge, or if you’re impatient or don’t have a 3D printer just grab one from Shapeways.

Pro tip: I found that copying my gCode into OpenOffice, coloring it pure red (#FF0000), and then re-pasting it back into Repetier-Host helped me get the extruder nozzle up to 282°C the second time around.